The update allows you to make a new key in both cases: when you have one working key and when all the keys are lost.

Magic Eraser allows to neutralize (bring back to "virgin" state) Mercedes-Benz ECU's, gearboxes, ESM/DSM modules and ELV'S. If you have one of those modules in "virgin" state you can program it into the car with the use of any diagnostics software

It includes software, a Bluetooth module and connection cables.

New device designed for on-bench testing of EZS (EIS), ESL (ELV).

Comes with ESL Emulator inside, has automatically mode switching - read ESL using and Emulation mode. You can test both old (Motorola based EZS) and new (NEC based) units without the car - just connect them with special set of cables.

Could be purchased in place of old devices: EIS cables set, ESL emulator, W204/207/212 + W221/215/164 testing cables.

A set of three Click'n go adapters for reading three types of SKREEM modules with MC68HC05 memory.

Supported models:

- Chrysler Crossfire 2003-2008

- Mercedes SLK Class R170 (all tyoes) 1996-2004

- Mercedes SL Class R129 1999-2001

- Mercedes A-Class W168 1997-2005

- Mercedes Vaneo W414 2001-2005

- Mercedes S-Class W140 06.1997-1999

- Mercedes G-Class W461 06.1997-2001

If you have the ML set you can upgrade your set to The MBE keymaker which allows you to make new keys on the following car models:

- 2007-2018 Dodge Sprinter W(C)906

- 2003-2008 Chrysler Crossfire

- 1996-2004 Mercedes SLK Class R170 (all types)

- 1999-2001 Mercedes SL Class R129

- 1997-2005 Mercedes A Class W168

- 2001 - 2005 Mercedes Vaneo W414

- 06.1997-1999 Mercedes S Class W140

- 06.1997-2001 Mercedes G-Class W461

The device allows you to make a new key in both cases: when you have one working key and when all the keys are lost.

Set includes:

- KR55 Remote Programmer device

- KR55 software

- 5 new keys ready to be programmed.

When you receive a new device, write an email to support@mbkeyprog.com and enter the order number and the SN number of your device (see manual below) to obtain the activation files.

If you have the Dodge/Sprinter set you can upgrade your set to The KR55 keymaker which allows you to make new keys on the following car models:

- 2007-2018 Dodge Sprinter W(C)906

- 2003-2008 Chrysler Crossfire

- 1996-2004 Mercedes SLK Class R170 (all types)

- 1999-2001 Mercedes SL Class R129

- 1997-2005 Mercedes A Class W168

- 2001 - 2005 Mercedes Vaneo W414

- 06.1997-1999 Mercedes S Class W140

- 06.1997-2001 Mercedes G-Class W461

The device allows you to make a new key in both cases: when you have one working key and when all the keys are lost.

Set includes:

- KR55 Remote Programmer device

- KR55 software

- 5 new keys ready to be programmed. (Please enter in your order which remotes to send).

When you receive a new device, write an email to support@mbkeyprog.com and enter the order number and the SN number of your device (see manual below) to obtain the activation files.

First in the world KR55 Keymaker - now with radio channel programming.

It works equally with lost keys and adding key!

The KR55 keymaker is a new device that allows you to make new keys on the following car models:

- 1997-2005 Mercedes A Class W168

- 1996-2004 Mercedes SLK Class R170 (all types)

- 2003-2008 Chrysler Crossfire

- 1999-2001 Mercedes SL Class R129

- 2001 - 2005 Mercedes Vaneo W414

- 06.1997-1999 Mercedes S Class W140

- 06.1997-2001 Mercedes G-Class W461

- 2007-2018 Dodge Sprinter W(C)906 (US/Canada market only)

The device allows you to make a new key in both cases: when you have one working key and when all the keys are lost.

Set includes:

- KR55 Keymaker device

- KR55 software + ML W163 Software + Truck keymaker software

- 5 new keys ready to be programmed.

- Cable set

This EEPROM programmer, was designed and developed by MBE Engineering to read EEPROM memories, especially the ones that are being used in older Mercedes-Benz keys. Coverage:

- Motorola 705 E6

- EEPROM 24C01/02/04/08/16/32/64/128/256/1024

- 93C46/56/66/76/86

- 95P02/04/08

- 95020/40/80/160/320/640

38 pins conection cable MB Key Prog 2 programation

This package of hardware and software allows to read basic information stored in Mercedes-Benz ignition locks (EIS/EZS). You can read SSID of ignition lock, HASH codes of keys and status of the keys (with use of colors).

Mini OBD Scan is a device allows you to get readings from vehicles via OBD II port .

This scanner will connect to your smartphone by Bluetooth by the Torque App, getting the following readings among many others:

- Reading of both generic and specific trouble and error codes and displays their meaning.

- Clears error codes and turns the "Check Engine" off.

- Engine's RPM.

- Calculated load value.

- Coolant temperature.

- Fuel System Status.

- Vehicle's speed.

- Long and short them fuel trim.

- Air temperature and pressure.

- Throttle absolut position.

- Fuel pressure.

- Air flow.

- Oxygene sensor voltage.

Here is an unique solution for replacing ESL/ELV. If you have faulty motor or ‘fatal error’, simply take out the ELS/ ELV and replace it with our EMULATOR BOX. New EVO repair kit works perfectly smooth with W204, W207 and W212 Mercedes-Benz ESLs (electronic steering locks), this kit requires ESL/ELV Evo software. EVO repair kit comes with EMULATOR box and token for Sonderhash website.

This cable reads and tests ESl and EZS en key and on bench. It supports W204, W207 and W212

It is used for CAN adapter, not for MB Key Prog2

This kit includes key programmer Mercedes ML MB Keymaker and software MB PCF Programmer

You can save more than a 30% getting this pack rather than purchasing both products separately. You will have acesso to a great amount of supported models.

ML MB Keymaker allows programming transponder keys based on PCF7935 into Mercedes Benz ML (WDB163). Also you can program new original remotes based on PCF7930.

Software MB PCF Programmer is used for programming keys with PCF transponder chip. It needs ML MB Keymaker for proper functioning. The supported models are: C202, E210, W140, Gelenvagen and A Class.

This software does not program by OBDII. It allows to program new PCF transponder chips only on used key places, so you have to detect number of the original key.

SUPPORTED IGNITION (CDI) / INJECTION CONTROLLERS

PHILIPS TSDI / DiTECH / PUREJET with TQFP-64 MC68HC908AZ60A (3K85K) MCU

READ/WRITE MC68HC908AZ60A internal EEPROM by K-Line

READ/WRITE external SPI EEPROM 25C160 by K-Line

READ MC68HC908AZ60A full 64K memory area

CLEAR FAULT MEMORY (NEW!)

RESET TO NEW / IMMO-OFF (NEW!)

MAGNETI MARELLI IAW 5AM HW103 / HW610 injection control module (HYBRID) with EEPROM 95160

READ / WRITE of external EEPROM 95160 by K-Line

RESET TO NEW (NEW!)

MAGNETI MARELLI with TQFP-64 MC68HC05Bxx (0D54J, 0D60J) MCU (system type ACI100, ACI50X, ACI60X)

READ / WRITE of MC68HC05B8/B16 internal EEPROM by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

CALCULATE CRC of key data blocks

EFI TECHNOLOGY with ST72C334 / ST72F521 MCU and 95040 / 95080 EEPROM (system type ACII, AC2I, AC5I, AC8I, AC19I, AC20I, AC21I, AC23I, AC25I AC32I etc.)

READ / WRITE of ST72C334 internal EEPROM by K-Line

READ / WRITE of external 95040 or 95080 SPI EEPROM by K-Line

READ data of TRANSPONDER KEY in the ignition lock by K-Line. Any of EFI TEECHNOLOGY CDI now can be used as a simple transponder reader for scooter keys

RESET of previously used CDI controller to the FACTORY state

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

CALCULATE CRC of key data block

MAGNETI MARELLI IMM003/IMM006 immobilizer module with 28 pin MC68HC05E6 (0F82B, 0G72G, 2F75B) MCU

READ / WRITE of MC68HC05E6 (0F82B / 0G72G) internal EEPROM by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

RESET of previously used Immobilizer Control Unit to the FACTORY state

MAGNETI MARELLI MIU1 (32MIU1) injection control module / throttle body with ST10F269-T3 MCU

READ KeyData memory block from FLASH of ST10F269-T3 by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

MAGNETI MARELLI MIU2 (32MIU2) injection control module / throttle body with ST10F269-T3 MCU and EEPROM 95160

READ KeyData memory block from FLASH of ST10F269-T3 by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

MAGNETI MARELLI MIU4 (32MIU4) injection control module / throttle body with ST10F269-T3 MCU and EEPROM 95160

READ KeyData memory block from FLASH of ST10F269-T3 by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

MAGNETI MARELLI MIU G3 (32M3G1 / 38M3G1) injection control module / throttle body with Infineon SAK-XC2060 and EEPROM 95320

READ / WRITE of external EEPROM 95320 by K-Line

CALCULATE both MASTER and SERVICE key data for programming into the T5-TYPE11 transponder

RESET of previously used Injection Control Unit to the FACTORY state

CALCULATE CRC

MAGNETI MARELLI IAW15 injection control module with MOTOROLA MC68HC11F1 (2E87J) MCU

READ / WRITE of internal MC68HC11F1 EEPROM by K-Line

CALCULATE MASTER key data for programming into the T5-TYPE11 transponder

RESET of previously used Injection Control Unit to the FACTORY state

CALCULATE CRC